environment protection specification model nes-100-5 nes-100-12 nes-100-9 nes-100-7.5 nes-100-15 nes-100-24 nes-100-48 dc voltage rated current current range rated power ripple & noise (max.) note.2 output voltage adj. range voltage tolerance note.3 line regulation note.4 load regulation note.5 setup, rise time hold up time (typ.) voltage range frequency range efficiency (typ.) ac current (typ.) input inrush current (typ.) leakage current safety standards working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage 5v 12v 9v 7.5v 15v 24v 48v 20a 8.5a 11.2a 13.6a 7a 4.5a 2.3a 0 ~ 20a 0 ~ 8.5a 0 ~ 11.2a 0 ~ 13.6a 0 ~ 7a 0 ~ 4.5a 0 ~ 2.3a 100w 102w 100.8w 102w 105w 108w 110.4w 80mvp-p 120mvp-p 120mvp-p 120mvp-p 120mvp-p 120mvp-p 150mvp-p 4.75 ~ 5.5v 11.4 ~ 13.2v 8.55 ~ 9.9v 7.13 ~ 8.3v 14.25 ~ 16.5v 22.8 ~ 26.4v 45.6 ~ 52.8v 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 85 ~ 132vac / 176 ~ 264vac selected by switch 248 ~ 373vdc 47 ~ 63hz 5.75 ~ 6.75v 13.8 ~ 16.2v 10.4 ~ 12.2v 8.6 ~ 10.1v 17.25 ~ 20.25v 27.6 ~ 32.4v 55.2 ~ 64.8v 80% 83% 81% 81% 84% 86% 86% 2a/115vac 1.2a/230vac cold start 36a <2ma / 240vac 110 ~ 150% rated output power ul60950-1, cb(iec60950-1),ccc gb4943 approved compliance to en55022 (cispr22) class b, en61000-3-2,-3 compliance to en61000-4-2,3,4,5,6,8,11, en55024, en61000-6- 1, light industry level, criteria a -20 ~ +60 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes 320.7khrs min. mil-hdbk-217f (25 ) 159*97*38mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. line regulation is measured from low line to high line at rated load. 5. load regulation is measured from 0% to 100% rated load. 6. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still mee ts emc directives. for guidance on how to perform these emc tests, please refer to ?emi testing of c omponent power supplies.? (as available on http://www.meanwell.com) file name:nes-100-spec 2011-08-17 0.55kg; 30pcs/17.5kg/0.97cuft 100w single output switching power supply n e s - 1 0 0 s e r i e s withstand voltage isolation resistance i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh safety & emc (note 6) protections: short circuit / overload / over voltage cooling by free air convection led indicator for power on 100% full load burn-in test 2 years warranty features : protection type : hiccup mode, recovers automatically after fault co ndition is removed protection type : hiccup mode, recovers automatically after fault co ndition is removed 500ms, 20ms/230vac 500ms, 20ms/115vac at full load 30ms/230vac 25ms/115vac at full load emc immunity emc emission
mechanical specification case no. 901 unit:mm terminal pin no. assignment pin no. pin no. 12 4,5 3 6,7 assignment assignment dc output -v dc output +v fg ac/l ac/n block diagram fosc : 60khz pwm circuit detection o.l.p. emi filter rectifiers 220 110 & filter power switching filter & rectifiers +v -v i/p control o.v.p. fg ambient temperature ( ) load (%) -20 0 20 10 30 40 20 40 50 80 60 100 60 50 70 +v adj. static characteristics input voltage (vac) 60hz load (%) 90 100 80 70 60 50 40 85 100 115 176 120 200 125 220 130 240 132 264 5v others (horizontal) derating curve 100w single output switching power supply n e s - 1 0 0 s e r i e s file name:nes-100-spec 2011-08-17 4.5 9 152.5 7 150 6.5 18.5 78 97 84.5 65 9.5 8.2 3.5 24 159 22 117 9 56 7 4 3 2 1 28.5 3-m3 3.5 3.5 2-m3 18 3.5 38
|
